Description
The TX2FX is an Ethernet media converter that translates transmission signals from a twistedpair 10/100/1000Base-TX cable to a 100Base-FX or 1000Base-X fiber optic cable. It expands network data transmission distances beyond the 100 meter limitation of copper wire to over 10 kilometers by using single-mode fiber optic cable.
For the fiber optic port any standard Small Form factor pluggable (SFP) transceiver module can be used on the TX2FX. These SFP transceivers modules are available with a variety of different transmitter and receiver types, allowing users to select the appropriate transceiver for the required fiber optical interface.
Further the TX2FX provides automatic detection and initializing of the SFP Module and has easy-to-read diagnostic LEDs for continuous status reports on network speed, traffic and fiber optic port status.
Features:
- Triple speed (10/100/1000Mbit) copper Ethernet interface
- Automatic detection and initializing of the SFP module (100Mbit-FX, 1000Mbit-X)
- Single wide power supply input (5 to 36V)
- Different mechanical versions
- Extended temp. option -40°C to +85°C
- Configurable Flow Control, Link Loss Forwarding and Link Speed Forwarding
- Jumbo Frame supported
- Unmanaged switch (TX2FX-13/TX2FX-14 only)
These features make the TX2FX ideally suited for any industrial application. Through the low power consumption, robust, and flexible design, the product can be used in any embedded system. Whether it is being used in a rugged, hot, or other extreme environment, the TX2FX helps to expand your network distances!
Technical Features:
| Board Key Data | ||
|---|---|---|
| Switch lookup Engine | support up to 1024 MAC entries with automatic learning and aging supports auto crossover (Auto MDI/MDIX) support polarity correction |
|
| Jumbo Frame support | up to 10k Byte | |
| Status LED | 2 LEDs for each copper port (Link/Activity and Speed indicators) 1 LED for each SFP (Link/Activity indicators) |
|
| Interfaces | ||
| Copper Ports | High quality RJ45 or M12 connectors (X-coded or D-coded) with lockable headers |
|
| Up to 2/4 Fiber Ports | Supports standard SFP Modules (Single and Multimode) at a data rate of 100Mbit and 1Gbit |
|
| Management Software | ||
| MPL developed and maintains a management SW with easy to use web interface. | ||
| Management supports: (Layer 2 Management) | IEEE 802.1X MAC Address Checking IEEE 802.1Q VLAN IEEE 802.1D RSTP support SNMP V1, V2c, V3 support IGMPv3 snooping DHCP Client Port monitoring | Switch statistic Port Based VLAN Quality of Service Accessible via https, Telnet, RS232 Firmware Update via HTTP or TFTP TLS (HTTPS) Trunking support (planned) |
| Power | ||
| Input (MAGBES-20) | 5VDC - 36VDC Input range | Input over 4-pin power connector |
| Input (MAGBES-10) | 5VDC | Input over 3-pin power connector or PC/104 bus interface |
| Power consumption | Typically 4W / 8W | 5-port / 8-port versions |
| Environment | ||
| Storage Temperature | -45°C up to +85°C (-49°F to +185°F) |
|
| Operating Temperature | -20°C to +60°C (-4°F to +140°F) at full operation optionally -40°C to +85°C (-40°F to +185°F) at full operation |
|
| Relative Humidity | 5% to 95% non condensing |
|
| Standard Compliance | ||
| The MAGBES is designed to meet or even exceed the most common standard Particular references are: | ||
| EMC | EN 55022, EN 55024, EN 61000, MIL-STD-461E |
|
| Shock & Vibration | EN 60068 |
|
| Environmental & Safety | EN 50155, MIL-STD-810-F, EN 60601, EN 60950 |
|
| Approval List | CE, IEC 60945, IACS E10 |
|
| The MAGBES family has been successfully tested according EN50155, MIL-STD-810-G as well as CE marking | ||
Accessories:
| Board Key Data | ||
|---|---|---|
| Switch lookup Engine | supports up to 1024 MAC entries with automatic learning and aging supports auto crossover (Auto MDI/MDIX) support polarity correction |
|
| Jumbo Frame support | up to 10k Byte | |
| Status LED | 2 LEDs for each copper port (Link/Activity and Speed indicators) | |
| Interfaces | ||
| LAN | µMAGBES-A10 - 10-port Gigabit on RJ45 connectors or 2mm lockable header µMAGBES-A19 - 19-port Gigabit on RJ45 connectors or 2mm lockable header µMAGBES-A28 - 28-port Gigabit on 2mm lockable header housing & connector kits for M12, RJ45, and Fiber |
|
| CLI | Optional CLI interface over Micro USB connector | |
| Management Software | ||
| MPL developed and maintains a management SW with easy to use web interface. | ||
| Management supports: (Layer 2 Management) | • IEEE 802.1X MAC Address Checking • IEEE 802.1Q VLAN • IEEE 802.1D RSTP support • SNMP V1, V2c, V3 support • IGMPv3 snooping • DHCP Client • Port monitoring | • Switch statistic • Port Based VLAN • Quality of Service • Accessible via https, Telnet, RS232 • Firmware Update via HTTP or TFTP • TLS (HTTPS) • Trunking support (planned) |
| Power | ||
| Input voltage | 5VDC- 36VDC Input range | input over 4-pin power connector |
| Power consumption | Typically 6W per 10 ports | |
| Environment | ||
| Storage Temperature | -45°C up to +85°C (-49°F to +185°F) | |
| Operating Temperature | -20°C to +60°C (-4°F to +140°F) at full operation optionally -40°C to +85°C (-40°F to +185°F) at full operation |
|
| Relative Humidity | 5% to 95% non condensing | |
| Standard Compliance | ||
| The µMAGBES is designed to meet or even exceed the most common standard, particular references are: | ||
| EMC | EN 55022, EN 55024, EN 61000, MIL-STD-461E | |
| Shock & Vibration | EN 60068 | |
| Environmental & Safety | EN 50155, MIL-STD-810-F, EN 60601, EN 60950 | |
| Approval List | CE, IEC 60945, IACS E10 | |
